KUC10010 HYDRAULIC EXCAVATORS CX800 Tier 3 Swing Motor

d:220.000 mm; Oil Speed Rating Open/Shielded n2:2200 rpm; B:56.00 mm; D:340.0000 mm; Basic Static Radial Load Rating Co:290000 N; Grease Speed Rating Open/Shielded n1:1800 rpm; Fillet Radius ra:2.50 mm; Sealed Speed Rating n3:1100 rpm; Accessories:Two Seals; Basic Dynamic Radial Load Rating C:247000 N;

l3 min.:37 mm; Basic dynamic load rating C:100 kN; d:40 mm; Mass rod end:2.4 kg; h1:105 mm; r1 min.:0.6 mm; dk:53 mm; C1 max.:23 mm; Tightening torque bolt with internal hexagon:45 N·m; B:28 mm;

Lock nut:N 040; B1:139.04 mm; B:30.429 mm; Lock washer:W 040; Sleeve:S 40x7.3/16; Mass adapter sleeve assembly:13 kg; G:199.314 mm; d3 max.:239.852 mm; Hydraulic nut:HMVC 40E; Threads per inch:8;

Cap bolt, SAE grade:8; Max. speed for Taconite seal:440 r/min; P60°:345 kN; PG:1/4 NPT; ba:69.85 mm; R2:33.337 mm; Taconite seal:TER 154; R1:104.775 mm; H1:169.875 mm; da:174.625 mm;

Fillet Radius ra:3.00 mm; Oil Speed Rating Open/Shielded n2:1700 rpm; d:280.000 mm; D:420.0000 mm; Sealed Speed Rating n3:890 rpm; Basic Static Radial Load Rating Co:405000 N; Grease Speed Rating Open/Shielded n1:1400 rpm; B:65.00 mm; Accessories:One Shield; Basic Dynamic Radial Load Rating C:302000 N;

C:45 mm; r1s (min):2.5 mm; Pu:53.910 kN; T:58 mm; Dynamic (Ca):341 kN; r2s (min):1 mm; d2:75 mm; rs (min):3 mm; D:160 mm; B:55 mm;

Bearing:23026 CCK/W33; Housing:SSAFS 026 KA; R2:31.75 mm; Eye bolt:2 x 3/8-16 UNC; Cap bolt:5/8-11 UNC; R1:73.025 mm; ba:51.594 mm; PG:1/4 NPT; P180°:72.5 kN; Cap bolt, SAE grade:8;

Cap bolt, SAE grade:8; Max. speed for Taconite seal:440 r/min; P60°:345 kN; PG:1/4 NPT; ba:69.85 mm; R2:33.337 mm; Taconite seal:TER 154; R1:104.775 mm; H1:169.875 mm; da:174.625 mm;

d:220.000 mm; Oil Speed Rating Open/Shielded n2:2200 rpm; B:56.00 mm; D:340.0000 mm; Basic Static Radial Load Rating Co:290000 N; Grease Speed Rating Open/Shielded n1:1800 rpm; Fillet Radius ra:2.50 mm; Sealed Speed Rating n3:1100 rpm; Accessories:Two Seals; Basic Dynamic Radial Load Rating C:247000 N;

B1:342 mm; d:710 mm; G3:13 mm; Mass adapter sleeve assembly:228 kg; B:90 mm; G2:G 1/8; Hydraulic nut:HMV 142E; A:8 mm; Locking device:MS 30/710; Lock nut:HM 30/710;

C:45 mm; r1s (min):2.5 mm; Pu:53.910 kN; T:58 mm; Dynamic (Ca):341 kN; r2s (min):1 mm; d2:75 mm; rs (min):3 mm; D:160 mm; B:55 mm;

C:45 mm; r1s (min):2.5 mm; Pu:53.910 kN; T:58 mm; Dynamic (Ca):341 kN; r2s (min):1 mm; d2:75 mm; rs (min):3 mm; D:160 mm; B:55 mm;

Lock nut:N 040; B1:139.04 mm; B:30.429 mm; Lock washer:W 040; Sleeve:S 40x7.3/16; Mass adapter sleeve assembly:13 kg; G:199.314 mm; d3 max.:239.852 mm; Hydraulic nut:HMVC 40E; Threads per inch:8;

Coefficient of friction µ max.:0.08; Tolerance shaft:h8; Mass bushing:1.25 kg; Effective load carrying cross section A:26700 mm²; Coefficient of friction µ min.:0.03; D:150 mm; Specific static load factor K0:200 N/mm²; d:165 mm; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7;

B:25 mm; d:25 mm; Tolerance shaft:h8; Permissible sliding velocity v min.:0.25 m/s; Specific dynamic load factor K:10 N/mm²; Tolerance housing:H7; Permissible sliding velocity v max.:5 m/s; D:30 mm; Mass bushing:0.036 kg; Specific static load factor K0:20 N/mm²;